Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL FITTINGS
Choose a sub category:
NON METALLIC CABLE CONNECTORS BX / FLEX CONDUIT FITTINGS EMT METAL CONDUIT FITTINGS
RIGID CONDUIT FITTINGS LIQUID TIGHT CONDUIT FITTINGS METAL CONDUIT ACCESSORIES
PVC CONDUIT FITTINGS SERVICE ENTRANCE FITTINGS GROUNDING RODS/CLAMPS
PLASTIC FLEXIBLE FITTINGS CONDUIT STRAPS WASHERS / REDUCERS
METAL CONDUIT SUPPORT
Sort By:
1
Carlon E940D-CTN Standard Conduit Coupling Carlon E943D-CTN Terminal Adapter Carlon E940E-CTN/CAR Standard Conduit Coupling
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Carlon E942DR-CTN Conduit Adapter Halex 97521 Insulated Conduit Bushing Carlon E940FR-CTN Standard Conduit Coupling
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Carlon E942ER-CTN Conduit Adapter Carlon E943E-CTN Terminal Adapter Halex 97525 Insulated Conduit Bushing
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Carlon E943FR-CTN Terminal Adapter Carlon Snap Strap E978DC-CAR 1-Hole Single Conduit Strap Halex 97522 Insulated Conduit Bushing
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Safe, non-conductive. To be used in accordance with NEC, Article 347.8 conduit spacing requirements. For use with Schedule 40/80 non-metallic solvent weld fittings. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Halex 96821 Rigid Reducing Conduit Washer Carlon E996DR-CTN Conduit Box Adapter Carlon E996ER-CTN Conduit Box Adapter
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. For PVC enclosures. cULus Listed. For PVC enclosures. cULus Listed.
Carlon E940GR-CTN Standard Conduit Coupling Carlon E942FR-CTN Conduit Adapter Carlon Snap Strap E978EC-CAR 1-Hole Single Conduit Strap
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Safe, non-conductive. To be used in accordance with NEC, Article 347.8 conduit spacing requirements. For use with Schedule 40/80 non-metallic solvent weld fittings.
Halex 96163 2-Hole Snap-On Conduit Strap Halex 90440 Screw-In Connector Halex 96191 Rigid IMC Conduit Locknut
To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Zinc die cast. Use to connect flexible metallic conduit (Greenfield) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Carlon A240D-CAR 1-Piece Conduit Coupling Halex 97523 Insulated Conduit Bushing Carlon UA7ADR-CAR Standard Radius Conduit Elbow
Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Carlon UA9ADR-CTN Standard Radius Conduit Elbow Carlon UA9AER-CTN Standard Radius Conduit Elbow Carlon E940HR-CTN Standard Conduit Coupling
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Carlon E943GR-CTN Terminal Adapter Carlon UA9ADB-CTN Standard Radius Rigid Conduit Elbow Halex 96192 Rigid IMC Conduit Locknut
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 96831 Rigid Reducing Conduit Washer Halex 96832 Rigid Reducing Conduit Washer Halex 96071 Knock Out Seals
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Carlon UA7ADB-CTN Standard Radius Conduit Elbow Halex 96560 Beam Clamp Halex 97524 Insulated Conduit Bushing
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Use to secure conduit to a metal beam. Clamps on beam, girder or similar structure to provide a mounting base for attachment of a conduit hanger, either directly or by means of a threaded rod. Eliminates need to drill hole through beam. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved.
Carlon UA7AER-CAR Standard Radius Conduit Elbow Carlon E942GR-CTN Conduit Adapter Carlon E943HR-CTN Terminal Adapter
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance.
Thomas & Betts E950ED-CTN Reducing Bushing Carlon A243D-CAR 1-Piece Snap-In Conduit Adapter Halex 96193 Rigid Conduit Locknut
For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Halex 90441 Screw-In Connector Halex 90451 Screw-In Coupling Halex 90701 Conduit Chase Nipple
Zinc die cast. Use to connect flexible metallic conduit (Greenfield) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. Zinc die cast. Use to join two pieces of flexible metallic conduit (Greenfield) together. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Halex 96111 1-Hole Conduit Strap Halex 96072 Knock Out Seals Carlon UA7AEB-CTN Standard Radius Conduit Elbow
Indoor or outdoor applications. Use to secure Rigid or I.M.C. conduit to wood, masonry or similar surfaces. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 26190 Conduit Locknut Halex 96194 Rigid IMC Conduit Locknut Carlon UA9AEB-CTN Standard Radius Rigid Conduit Elbow
Halex Conduit Locknut, 1/2 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Halex 91530 Combination Coupling Carlon A253D-CAR 1-Piece Snap-In Terminal Adapter Carlon A253E-CAR 1-Piece Snap-In Terminal Adapter
Zinc die cast. Use to join EMT conduit to non-metallic sheathed cable. #14/2, #12/3 or 2 #14/2. Indoor use only. With UPC. UL Approved. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Carlon E940JR-CTN Standard Conduit Coupling Carlon E942HR Conduit Adapter Thomas & Betts E977DC-CTN 2-Hole Conduit Clamp
Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit.
Halex 96780 Conduit Hanger Halex 96151 1-Hole Snap-On Conduit Strap Halex 96161 2-Hole Snap-On Conduit Strap
Use to secure and suspend conduit from overhead supports. Comes with a nut and bolt. Indoor or outdoor applications. To support EMT conduit. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications.
Halex 90580 Cable Connector Halex 90510 Twin Screw Clamp Connector Halex 96121 2-Hole Conduit Strap
Zinc die cast. In a dry location, use to connect BX cable to a steel outlet box or other metal enclosure. 3/8" size fits 1/2" knock outs. UL Approved. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved.
Halex 91321 Reducing Conduit Bushing Halex 96781 Conduit Hanger Halex 64305 Intermediate Rigid Conduit Nipple
Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Use to secure and suspend conduit from overhead supports. Comes with a nut and bolt. Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, Close Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor
Halex 64311 Intermediate Rigid Conduit Nipple Halex 96843 Rigid Reducing Conduit Washer WASHER RDUCNG RGD 1-1/4X1/2IN
Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 1-1/2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
WASHER RDUCNG RGD 1-1/4X3/4IN Carlon A240E-CAR 1-Piece Conduit Coupling Halex 91641 Box Spacer
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed.
Carlon UA9AFR-CTN Standard Radius Conduit Elbow Carlon E943JRR Terminal Adapter Thomas & Betts E977EC-CTN 2-Hole Conduit Clamp
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit.
Carlon UA7AFR-CAR Standard Radius Conduit Elbow Halex 90570 Combination Clamp Connector Halex 96213 1-Hole Cable Strap
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield, BX, NM or Metal Clad) to a steel outlet box or other metal enclosure. 3/8" size fits 1/2" knock outs. UL Approved. Steel, use to secure BX cable to wood, masonry or similar surface.
Halex 96112 1-Hole Conduit Strap Halex 26197 Conduit Locknut Halex 27528 Insulating Bushing
Indoor or outdoor applications. Use to secure Rigid or I.M.C. conduit to wood, masonry or similar surfaces. Halex Conduit Locknut, 3/4 in Nominal, Steel, Zinc Plated, CSA Certified, UL Listed, For use to secure rigid, imc conduit or various threaded fittings to a steel outlet box or other metal enclosure, indoor/outdoor Halex Insulating Bushing, 1 in Conduit, Rigid, IMC Conduit, Threaded End, Thermoplastic, UL Listed, CSA Certified, For Indoor/Outdoor Applications
Carlon A243E-CAR 1-Piece Snap-In Conduit Adapter Halex 96195 Rigid Conduit Locknut Carlon E942JR Conduit Adapter
Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Carlon UA7AFB-CTN Standard Radius Conduit Elbow Halex 96162 2-Hole Snap-On Conduit Strap Halex 90442 Screw-In Connector
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Zinc die cast. Use to connect flexible metallic conduit (Greenfield) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs.
Halex 91100 Conduit Elbow Halex 90420 Squeeze Connector Halex 96510 2-Piece Butterfly Clamp Connector
Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to a steel outlet box or other metal enclosure. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. UL Approved. Zinc die cast. In a dry location, use to secure #14 - #10 non-metallic sheathed cable to steel outlet box or other metal enclosure. No locknut required.
Halex 96122 2-Hole Conduit Strap Halex 91331 Reducing Conduit Bushing Halex 91332 Reducing Conduit Bushing
Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved. Zinc die cast. Indoor or outdoor applications. Use to reduce the entry size of a run of threaded conduit. UL Approved.
Halex 96142 Flat Style Drive Strap STRAP CBL 1HOLE SRVC ENT      WASHER RDUCNG RGD 1-1/2X1/2IN
Halex Drive Strap, Flat Style, 3/4 in Nominal, Steel/Nylon, Zinc Plated, 2.12 in Length x 1.2 in Width, CSA Certified, UL Listed, For Indoor/Outdoor Applications Indoors or outdoors. Steel, use to secure service entrance cable (SEU, SER) to wood, masonry or similar surface. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
WASHER RDUCING RGD 1-1/2X3/4IN Thomas & Betts E994DR-CTN Conduit Offset Halex 96152 1-Hole Snap-On Conduit Strap
Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Non-conductive. Will not rust or corrode. Indoor or outdoor applications. To support EMT conduit.
Halex 90421 Squeeze Connector Halex 64325 Intermediate Rigid Conduit Nipple Halex 64307 Conduit Nipple
Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. UL Approved. Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Nipple, 3/4 in Nominal, Steel, Galvanized, Close Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor
Thomas And Betts Z703 1/2-25 Superstrut Halex 26071 Knock Out Seals Halex 61225 2-Hole Conduit Strap
Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications.
Gardner Bender GGS-1512R Ground Screw Halex 97526 Insulated Conduit Bushing Carlon UA9AFB-CTN Standard Radius Conduit Elbow
Green round washer head screw for switch and outlet boxes. High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Carlon UA9AGR-CTN Standard Radius Conduit Elbow Carlon E950FD-CAR Reducing Conduit Bushing Carlon UA7AGR-CAR Standard Radius Conduit Elbow
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 75403 Anti-Short Conduit Bushing Carlon E940K-CTN Conduit Coupling Halex 27511 Hit Lock Cable Connectors
High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed. Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified.
Halex 26155 1-Hole Snap-On Conduit Strap Halex 90512 Twin Screw Clamp Connector Halex 90702 Conduit Chase Nipple
Indoor or outdoor applications. To support EMT conduit. Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Halex 27527 Insulating Bushing Halex 64005 Conduit Coupling Thomas & Betts 700 Pipe Clamp
Halex Insulating Bushing, 3/4 in Conduit, Rigid, IMC Conduit, Threaded End, Thermoplastic, UL Listed, CSA Certified, For Indoor/Outdoor Applications Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Thomas & Betts Pipe Clamp, Universal, Series: 700, 1/2 in Opening, 400 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 16 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 0.706 - 0.84 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling
Thomas & Betts 700 Pipe Clamp CONNECTOR DPLX FLX N-MTL 3/8IN Halex 90513 Twin Screw Clamp Connector
Thomas & Betts Pipe Clamp, Universal, Series: 700, 3/4 in Opening, 550 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 0.932 - 1.05 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling In a dry location, use to connect two pieces of flexible armored cable (Greenfield or BX) to a steel outlet box or other metal enclosure, when using only one knock-out opening. UL Approved. Fits non metallic cable number 14/2 to number 6/3 AWG or number 3/10/3 AWG or flex cord .450 to .730 inches diameter. With a 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements.
Halex 91531 Combination Coupling Halex 26165 2-Hole Snap-On Conduit Strap Halex 90422 Squeeze Connector
Zinc die cast. Use to join EMT conduit to flexible metal conduit. Indoor use only. With UPC. UL Approved. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. UL Approved.
Halex 26211 1-Hole Conduit Strap Halex HX Flexible Screw-In Connector Halex 26072 Knock-Out Seal
Steel, use to secure BX cable to wood, masonry or similar surface. Halex Screw-In Connector, Flexible, Series: HX, 1 in Nominal, Straight, 1.37 in Hex, Die Cast Zinc, 1.94 in Length, CSA Certified, UL Listed, 1 in Male NPSM Hub, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Halex Knock-Out Seal, 3/4 in Nominal, Steel, Zinc Electro Plated, 1-1/4 in Length X 0.313 in Width, CSA Certified, UL Listed, For use to cover exposed knockout holes in steel outlet boxes and other metal enclosures, indoor use only
Thomas & Betts E940E5-UPC Conduit Coupling Halex 26210 1-Hole Service Entrance Strap Superstrut 200 Series Angle Bracket Fitting
Thomas & Betts Conduit Coupling, 3/4 in Conduit, Rigid Conduit, Socket End, SCH 40, PVC, 0.84 in ID X 1-5/16 in OD Diameter, 1-5/8 in Length, cULus E 32447, RoHS Compliant Indoors or outdoors. Steel, use to secure service entrance cable (SEU, SER) to wood, masonry or similar surface. For use in metal framing applications. Manufactured from hot rolled carbon steel.
Thomas And Betts Z703 3/4-25 Superstrut Halex 90514 Twin Screw Clamp Connector Halex 20511 Twin Screw Clamp Connector
Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Fits non metallic cable number 6/3 to number 2/3 AWG flex cord .800 to 1.350 inches diameter or SE cable 3 conductor or 3 number 1/0 minimum; 3 conductor or 3 number 2/0 maximum. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements.
Halex 64007 Conduit Coupling Carlon UB9AD-CAR Standard Radius Conduit Elbow Thomas & Betts E950FE-CTN Reducing Bushing
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode.
Thomas & Betts E994ER-CTN Conduit Offset Carlon UA7AGB-CAR Standard Radius Conduit Elbow Halex 26125 2-Hole Conduit Strap
Non-conductive. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved.
Carlon E943K-CTN Terminal Adapter Carlon LN43DA-CTN Liquidtight Straight Angle Conduit Connector Halex 26153 1-Hole Snap-On Conduit Strap
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. For flexible conduit. Non-metallic/non-conductive, corrosion resistant plastic. Indoor or outdoor applications. To support EMT conduit.
Halex 91101 Conduit Elbow Halex 96401 Conduit Coupling Halex 96196 Rigid IMC Conduit Locknut
Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to a steel outlet box or other metal enclosure. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Steel with zinc plating. Indoor or outdoor applications. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure.
Carlon E977LC-CAR Conduit Clamp Halex 64327 Intermediate Rigid Conduit Nipple Halex 64331 Intermediate Rigid Conduit Nipple
Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. Halex Conduit Nipple, Intermediate, Rigid, 3/4 in Nominal, Steel, 2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, Galvanized, 3 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor
Halex 64341 Intermediate Rigid Conduit Nipple Halex 64361 Intermediate Rigid Conduit Nipple Halex 26212 1-Hole Corrosion Resistant Midget Strap
Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 4 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Nipple, Intermediate, Rigid, 1/2 in Nominal, Steel, 6 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Midget Strap, 1-Hole, Corrosion Resistant, 3/16 in Opening, Galvanized Steel, Electro Plated Zinc, 0.73 in Width, For Indoor/Outdoor Applications
Thomas & Betts 700 Pipe Clamp Thomas And Betts Z703 1-25 Thomas And Betts Z703 1 1/4-10 Superstrut
Thomas & Betts Pipe Clamp, Universal, Series: 700, 1 in Opening, 550 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 1.163 - 1.315 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish.
Superstrut 200 Flat Straight Bracket Splice Plate 7-1/4 in L Thomas & Betts E977FC-CTN 2-Hole Conduit Clamp Thomas And Betts Z702 21/2EG-10 Superstrut Pipe Clamp
Splices and supports conduit. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt.
Halex 75400 Anti-Short Conduit Bushing Gardner Bender GCC-310 2-Hole Conduit Strap Carlon E940LR/CTN Conduit Coupling
High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4. Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Safe, non-conductive. Schedule 40 non-metallic socket type coupling for joining Schedule 40 non-metallic conduit. Will not rust or corrode. RoHS Compliance, UL Listed.
Halex 75225 Insulated Conduit Bushing Carlon UA9AH-CAR Standard Radius Conduit Elbow Thomas & Betts E986D-CTN Type LB Rigid/IMC Conduit Body
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance.
Carlon UA7AHR-CTN Standard Radius Conduit Elbow Carlon E985D-CTN Rigid Conduit Body Carlon E984D-CTN Rigid Conduit Body
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297. For easy access and pulling of wires through conduit run. Textured lid, foam-in-place gasket. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Halex 26126 2-Hole Conduit Strap Halex 26163 2-Hole Snap-On Conduit Strap Halex 90452 Screw-In Coupling
Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Zinc die cast. Use to join two pieces of flexible metallic conduit (Greenfield) together.
Halex 96402 Conduit Coupling Halex 64342 Intermediate Rigid Conduit Nipple Halex 20701 Rigid Conduit Chase Nipple
Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. Halex Conduit Nipple, Intermediate, Rigid, 3/4 in Nominal, Steel, 4 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Halex Conduit Chase Nipple, Rigid, 1/2 in Nominal, Die Cast Zinc, 1.02 in Length X 0.68 in Width, CSA Certified, UL Listed, For use with a rigid coupling to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. used with a locknut to provide a short raceway between boxes or enclosures, indoor/outdoor
Halex 64362 Intermediate Rigid Conduit Nipple Thomas & Betts E943E5 Terminal Adapter Halex 27251 Snap-In Bushing
Halex Conduit Nipple, Intermediate, Rigid, 3/4 in Nominal, Steel, 6 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Thomas & Betts Terminal Adapter, Series: E943E5, 3/4 in Conduit, Rigid Conduit, Male Thread X Socket End, SCH 40, PVC, 1-3/8 in Length, UL E 32447, RoHS Complaint, cUL Listed, For Adapting Non-Metallic Conduits to Boxes, Threaded Fittings and Metallic Systems Halex Snap-In Bushing, 1/2 in Trade, 0.72 in Inside Diameter, 0.99 in Outside Diameter, 0.36 in Thickness, Plastic, Snap-In Insulation, For Indoor Applications
Thomas And Betts Z703 1 1/2-10 Superstrut Thomas & Betts 700 Pipe Clamp Superstrut 200 Series Angle Bracket Fitting
Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish. Thomas & Betts Pipe Clamp, Universal, Series: 700, 1-1/4 in Opening, 800 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 1.508 - 1.66 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling For use in metal framing applications. Manufactured from hot rolled carbon steel.
Thomas And Betts Z500-25 Superstrut Beam Clamp STRAP CBL 1HOLE OVAL SRVC ENT Eritech ZWP1J Grounding Pipe Clamp
For hanging rod, silver electroplated finish. Indoors or outdoors. Steel, use to secure service entrance cable (SEU, SER) to wood, masonry or similar surface. Bolted water pipe clamps made of zinc die-cast. Wire range 8 sol. - 2 str. UL Listed. Connects grounding wire to the grounding rod.
Carlon UA9AGB-CTN Standard Radius Conduit Elbow Halex 90662 Standard Water-Tight Connector Eritech CP58 Acorn Standard Duty Ground Clamp
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Connects grounding wire to the grounding rod. UL and CSA Listed for 1/2" and 5/8" ground rods and number 4 rebar and accept a conductor range from number 10 solid to number 2 stranded.
Thomas & Betts E977GC-CTN 2-Hole Conduit Clamp Thomas & Betts E950GF-CTN Reducing Bushing Carlon E950GE-CAR Reducing Conduit Bushing
Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode.
Halex 26166 2-Hole Snap-On Conduit Strap Halex 26154 1-Hole Snap-On Conduit Strap Carlon E987D-CTN Rigid Conduit Body
To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Indoor or outdoor applications. To support EMT conduit. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed.
Carlon LN43EA-CTN Liquidtight Straight Angle Conduit Connector Halex 90661 Standard Water-Tight Connector Halex 93591 Ground Clamp
For flexible conduit. Non-metallic/non-conductive, corrosion resistant plastic. Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Connects grounding wire to the grounding rod.
Halex 90703 Conduit Chase Nipple Halex 27362 Conduit Coupling Thomas & Betts E943D10 Terminal Adapter
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Halex Conduit Coupling, 3/4 in Conduit, Liquid-Tight Conduit, Slip End, PVC, CSA Certified, UL Listed, For Weatherproof Outlet Boxes, Pool And Spa Equipment Motors, Central Air Conditioning Units and Various Other Electrical Enclosures And Hubs Thomas & Betts Terminal Adapter, Series: E943D10, 1/2 in Conduit, Rigid Conduit, Male Thread X Socket End, SCH 40, PVC, 1-5/16 in Length, UL E 32447, RoHS Complaint, cUL Listed, For Adapting Non-Metallic Conduits to Boxes, Threaded Fittings and Metallic Systems
Halex 27252 Snap-In Bushing Thomas And Betts Z702 3EG-10 Superstrut Carlon UA7AHB-CAR Standard Radius Conduit Elbow
Halex Snap-In Bushing, 3/4 in Trade, 0.95 in Inside Diameter, 1.22 in Outside Diameter, 0.36 in Thickness, Plastic, Snap-In Insulation, For Indoor Applications Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 64312 Fully Threaded Conduit Nipple Thomas & Betts E950HGR Reducing Bushing Gardner Bender GGP-1502 Grounding Pigtail
Made of steel, fully threaded. Indoor or outdoor. Use to connect two steel outlet boxes or other metal enclosures or to extend a length of threaded Rigid or IMC conduit. Bulk packed. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. AWG solid number 12 wire. 8" long with captured screw, other end bare fork terminal.
Carlon E943L-CAR Terminal Adapter Gardner Bender 14-GRC Ground Clamp Carlon E983D-CTN Rigid IMC Conduit Body
Safe, non-conductive. For adapting schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Male threads on one end, socket end on the other. Will not rust or corrode. UL Listed, RoHS Compliance. Connects grounding wire to the grounding rod. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Halex 75401 Anti-Short Conduit Bushing Halex 27250 Snap-In Bushing Halex 26156 1-Hole Snap-On Conduit Strap
High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4. Use to protect non-metallic cable from damage when running cable through metal studs. Fits a variety of pre-punched metal stud openings. Indoor or outdoor applications. To support EMT conduit.
Halex 75230 Insulated Conduit Bushing Halex 20581 Cable Connector Halex 19005 Short Radius Rigid IMC Conduit Elbow
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. In a dry location, use to connect AC (BX) cable to a steel outlet box or other metal enclosure. Suitable for #14-2 steel armored cable. Halex Conduit Elbow, Short Radius, Rigid, IMC, 90 deg, 1/2 in Conduit, Threaded End, Die Cast Zinc, CSA Certified, UL Listed, For use to connect rigid or IMC conduit to an outlet box where a close radius is desired, indoor/outdoor
Thomas & Betts E940D10-UPC Conduit Coupling Gardner Bender GCC-410 2-Hole Conduit Strap Superstrut 200 Flat Right Angle Bracket Corner Plate
Thomas & Betts Conduit Coupling, 1/2 in Conduit, Rigid Conduit, Socket End, SCH 40, PVC, 0.728 in ID X 1-7/64 in OD Diameter, 1-1/2 in Length, cULus E 32447, RoHS Compliant Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Splices and supports conduit.
Gardner Bender GCC-220 2-Hole Conduit Strap Gardner Bender GCC-510 2-Hole Conduit Strap Halex 64010 Conduit Coupling
Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Gardner Bender GGC-1508 Ground Clip Halex 61230 2-Hole Conduit Strap Carlon E942K-CAR Conduit Adapter
For aluminum or copper grounding wire zinc plated. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode.
Fishock GRC-FS Ground Clamp Carlon UB9AE-CAR Standard Radius Conduit Elbow Carlon E983E-CTN Rigid IMC Conduit Body
Helps to make a superior connection of ground wire to ground rod. Heavy duty construction for long usage. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Thomas & Betts E977HC-CTN 2-Hole Conduit Clamp Carlon E985E-CTN Rigid Conduit Body Carlon E984E-CTN Rigid Conduit Body
Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. For easy access and pulling of wires through conduit run. Textured lid, foam-in-place gasket. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Halex 91625 Multi-Piece Liquid Tight Compression Connector Halex 26164 2-Hole Snap-On Conduit Strap Halex 75402 Anti-Short Conduit Bushing
Zinc die cast. Use to connect liquid-tight conduit to a steel outlet box, metal enclosure or hub. UL Approved. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. High dielectric plastic. Use to protect wire within flexible metallic conduit (Greenfield, BX). Insert one bushing at each end of conduit. UL Approved. No. 75400 - Fits cable range: 14/2, 14/3, 12/2 No. 75401 - Fits cable range: 14/4, 12/3, 6/1, 4/1. No. 75402 - Fits cable range: 12/4, 10/2, 10/3, 2/1. No. 75403 - Fits cable range: 10/4, 8/2, 8/3, 1/1. No. 75404 - Fits cable range: 8/4, 6/2, 6/3, 4/2, 4/3, 6/4.
Carlon Carflex LN20DA-CTN Liquidtight Conduit Elbow Carlon Carflex LN20EA-CTN Liquidtight Conduit Elbow Halex 91102 Pull Conduit Elbow
For flexible conduit. Non-metallic, Non-conductive, corrosion resistant plastic. For flexible conduit. Non-metallic, Non-conductive, corrosion resistant plastic. Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to a steel outlet box or other metal enclosure.
Halex 27519 Hit Lock Cable Connectors Halex 26073 Knock Out Seals Carlon E950JHR Reducing Conduit Bushing
Fits NM Cable: #14/2, #14/3, #12/2, #10/2, #10/3. Snap-In, no screws or locknuts required. In a dry location, use to connect non-metallic sheathed cable to a steel outlet box or other metal enclosure. Design allows for two-step installation. Push into box and insert cable. UL Approved, CSA certified. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode.
Halex 20570 Combination Clamp Connector Halex 64313 Intermediate Rigid Conduit Nipple Gardner Bender GCC-120 2-Hole Conduit Strap
In a dry location, use to connect flexible metallic conduit, AC, MC, or NM cable to steel outlet box or other enclosure. Fits 1/2" knockout. Suitable For: #14/2 thru 12/3 with ground NM sheathed cable, #14-2 wire steel armored cable, 3/8" steel flexible metal conduit and steel interlocked metal clad cable 0.435-0.547" diameter. UL, CSA approved. Halex Conduit Nipple, Intermediate, Rigid, 1 in Nominal, Steel, Galvanized, 2 in Length, CSA Certified, UL Listed, For use to connect two steel outlet boxes or other metal enclosures; use to extend a length of threaded rigid or IMC conduit, indoor/outdoor Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing.
Thomas & Betts 700 Pipe Clamp Superstrut 200 Series Flat Straight Bracket Halex 36010 Ground Clamp
Thomas & Betts Pipe Clamp, Universal, Series: 700, 2 in Opening, 800 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 2.195 - 2.375 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling Splices and supports conduit. Indoor or outdoor applications. Use to secure the grounding wire to a 1/2" through 1" pipe. UL Listed. Wire size fits #10 - #2 AWG.
Carlon UB9AF-CAR Standard Radius Conduit Elbow Thomas & Betts E986E-CTN Type LB Rigid/IMC Conduit Body Thomas & Betts E977JCR-CTN 2-Hole Conduit Clamp
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit.
Halex 07012 Conduit Chase Nipple Carlon UA9AJ-CAR Standard Radius Conduit Elbow Thomas & Betts E986F-CTN Type LB Rigid/IMC Conduit Body
Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance.
Carlon E983FR-CTN Rigid IMC Conduit Body Halex 64405 Conduit Elbow Carlon UA7AJ-CAR Standard Radius Conduit Elbow
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. To connect EMT conduit together to allow for 90 degree bends. UL Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 27621 Multi-Piece Liquid Tight Straight Conduit Connector Halex 27352 Terminal Adapter Halex 26214 1-Hole Corrosion Resistant Midget Strap
Fitting will not rust or corrode. No disassembly required. Reusable, hand tightened nut. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. Halex Terminal Adapter, 3/4 in Conduit, Male End, PVC, 5 in Length, For Indoor/Outdoor Applications Halex Midget Strap, 1-Hole, Corrosion Resistant, 1/4 in Opening, Galvanized Steel, Electro Plated Zinc, 0.95 in Width, For Indoor/Outdoor Applications
Thomas & Betts 700 Pipe Clamp LOCK NUT SEALER 1/2IN         Halex 05115 Twin Screw Clamp Connector
LOCK NUT SEALER 1/2IN
Our Price: $3.49
Thomas & Betts Pipe Clamp, Universal, Series: 700, 1-1/2 in Opening, 800 lb Load Capacity, Steel, ASTM A569, Electro Galvanized, Silver, 1-1/4 in Height, 14 ga Thickness, Includes: Bolt and Square Nut, OSHA Approved, 1.738 - 1.9 in Cable, For Suspend Electrical Pipes and Tubing From the Ceiling Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Fits non metallic cable, flex cords, multi flex cords; fitting range .834 - 1.520 inches diameter SE cables 2 conductor 4/0. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed.
Carlon E987E-CTN Rigid Conduit Body Halex 26074 Knock Out Seals Carlon UA7AJB-CAR Standard Radius Conduit Elbow
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 07310 Compression Standard Water-Tight Connector Teddico/BWF 500V Thinwall Rigid Conduit Entrance Elbow Halex 64012 Conduit Coupling
Die cast of high strength zinc alloy. Use to secure SE/SEU cable to a metal enclosure. Use to connect UF cable to a waterproof box with a threaded hub. Teddico/BWF Conduit Entrance Elbow, Thinwall, SLB, 1/2 in Hub, Rigid Conduit, Threaded Installation, Die Cast Aluminum, Gray, Powder Coated, Includes: Cover and Screw, CSA Certified, UL Listed, For connecting conduit sections, making bends in conduit runs as pull outlets, to provide openings for making splices and taps in conductors Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Halex 27361 Conduit Coupling Thomas & Betts E984F-CAR Rigid Conduit Body Thomas & Betts E985F-CAR Rigid Conduit Body
Halex Conduit Coupling, 1/2 in Conduit, Liquid-Tight Conduit, Slip End, PVC, CSA Certified, UL Listed, For Weatherproof Outlet Boxes, Pool And Spa Equipment Motors, Central Air Conditioning Units and Various Other Electrical Enclosures And Hubs Thomas & Betts Conduit Body, LL, 1 in Hub, Rigid Conduit, Foam, Non-Threaded Installation, 6-9/32 in Length, 2-1/32 in Width, PVC, CSA Certified, UL Listed Thomas & Betts Conduit Body, LR, 1 in Hub, Rigid Conduit, Foam, Non-Threaded Installation, 6-9/32 in Length, 2-1/32 in Width, PVC, CSA Certified, UL Listed
Teddico/BWF 181V Clamp Service Entrance Head Gardner Bender GCC-610 2-Hole Conduit Strap Carlon Z703 2 Pipe Clamp
Teddico/BWF Service Entrance Head, Clamp, 3/4 in Trade, Gray Heavy-duty polyethylene, resists deterioration from UV rays and breakage from extreme cold. Enables secure fastening of plastic electrical conduit, schedule 40 PVC, copper tubing. Pipe straps hold conduit and pipes in channel. They are inserted along the slot side of the channel and twisted into place. Pre-assembled with locking slot / hex head bolt. Gold-galvanized corrosion free finish.
Superstrut ZCM1001/4-10 Cone Nut WASHER REDUCING 2X1IN         WASHER REDUCING 2X1-1/4IN
WASHER REDUCING 2X1IN
Our Price: $3.79
Superstrut Cone Nut, 1/4 in Nominal, Nylon Cone, Steel Nut, Galvanized, Gold, For Superstrut Metal Framing and Hanger System Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved.
Carlon UA9AHB-CTN Standard Radius Rigid Conduit Elbow Halex 26075 Knock Out Seals Eritech CWP1J Grounding Pipe Clamp
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures. Bolted water pipe grounding clamp. UL listed. Made of corrosion-resistant copper alloy.
Carlon E942L-CAR Conduit Adapter Carlon E990DR-CAR Access Pull Standard Radius Conduit Elbow Halex 58305 Rigid Threaded Conduit Body with Cover and Gasket
Safe, non-conductive. For adapting Schedule 40 non-metallic conduit to boxes, threaded fittings, metallic systems. Female threads one end, socket end on the other. Will not rust or corrode. Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 58405 Rigid Threaded Conduit Body with Cover and Gasket Halex 58605 Rigid Threaded Conduit Body with Cover and Gasket Halex 58905 Rigid Threaded Conduit Body with Cover and Gasket
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 94105 Pull Conduit Elbow with Neoprene Gasket Carlon E987F-CAR Rigid Conduit Body Carlon UA9AJB-CAR Standard Radius Conduit Elbow
Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed.
Carlon UAFAD Flexible Conduit Elbow Halex 20440 Flexible Screw-In Connector Halex 93592 Ground Clamp
Made of a highly durable plastic (PVC) compound making the product nonmetallic and safe to install. Elbow is non-corrosive, rustproof, and easily pliable. Good for those applications that requires change of direction. UL listed. Halex Screw-In Connector, Flexible, 1/2 in Nominal, 0.92 in Hex, Die Cast Zinc, 1.38 in Length, CSA Certified, UL Listed, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Connects grounding wire to the grounding rod.
Carlon E995GR Meter Offset Carlon E990ER-CAR Access Pull Standard Radius Conduit Elbow Halex 07015 Conduit Chase Nipple
For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode. Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved.
Halex 58005 Standard Weatherhead Service Entrance Cap Thomas And Betts ZA1001/4EG-10 Superstrut Thomas And Betts Z502-10 Superstrut Beam Clamp
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. For use with 'A' and 'C' series channel and inserts. For hanging rod, silver electroplated finish.
Halex 05120 Twin Screw Clamp Connector Halex 04010 Offset Nipple Halex 64015 Conduit Coupling
Fits non metallic cable, flex cords, multi flex cords fitting range 1.085 - 1.520 inches diameter. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Tray boxed. Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed.
Carlon E995J-CTN Meter Offset Carlon UB9AG-CAR Standard Radius Conduit Elbow Thomas & Betts E986GR Type LB Rigid/IMC Conduit Body
For installation from Schedule 40/80 non-metallic conduit runs into meter box. Will not rust or corrode. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance.
Halex 26151 1-Hole Snap-On Conduit Strap Halex 26141 Flat Drive Strap Halex 20491 Combination Coupling
Indoor or outdoor applications. To support EMT conduit. Indoors or outdoors. To secure EMT conduit to a wood or masonry surface. Use to joint EMT conduit to flexible metal conduit. Die cast zinc. UL Approved, CSA Certified.
Halex 27622 Multi-Piece Liquid Tight Straight Conduit Connector Halex 27691 Liquid Tight Conduit Elbow Halex 59505 Service Entrance Elbow
Fitting will not rust or corrode. No disassembly required. Reusable, hand tightened nut. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. Indoors or outdoors, fitting will not rust or corrode. No disassembly required, just hand-tighten nut. Reusable. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed.
Carlon E990DER-CAR Pull Elbow With Reducer Bushing Teddico/BWF 300-CGV Thinwall Conduit Body Assembly Teddico/BWF 600-CGV Thinwall Conduit Body Assembly
Access pull point for cable in tight radius. Allows conduit changes in direction. Won't rust or corrode. Gasket included. Teddico/BWF Conduit Body Assembly, Thinwall, C, 1/2 in Hub, 2 Hubs, Side Access Opening, Straight Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Teddico/BWF Conduit Body Assembly, Thinwall, LB, 1/2 in Hub, Back Side Access Opening, Stamped Aluminum Cover, Threaded Installation, 15-1/2 in Length, 8-1/2 in Width, 5-3/4 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling
Halex 58007 Clamp On Weatherhead Service Entrance Cap Halex 36110 Ground Clamp Thomas And Betts ZA1003/8EG-10 Superstrut
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. Indoor or outdoor. Wire size fits number 8 - number 4 AWG. Use to secure the grounding wire to a 1/2" through 1" pipe. Bronze, bagged. UL Listed. For use with 'A' and 'C' series channel and inserts.
Thomas And Betts ZU501-10 Superstrut Beam Clamp Steel City ZCK535-10 Armored Cable Hanger Clip Halex 26152 1-Hole Snap-On Conduit Strap
For channel. 3-1/16". Flexible conduit hanger from drop wire, #8-#12 wire, .433-.535 O.D. cable. Indoor or outdoor applications. To support EMT conduit.
Halex 94107 Pull Conduit Elbow Halex 21642 Box Spacer Halex 26161 2-Hole Snap-On Conduit Strap
Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed. Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosures. UL and CSA Listed. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications.
Carlon E998E-CAR Service Entrance Cap Halex 91627 Multi-Piece Liquid Tight Conduit Connector Halex 58805 Rigid Threaded Conduit Body with Cover and Gasket
Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Zinc die cast. Use to connect liquid-tight conduit to a steel outlet box, metal enclosure or hub. UL Approved. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed.
Halex 27351 Terminal Adapter Thomas And Betts ZA1001/2EG-10 Superstrut Carlon E998F-CAR Standard Weatherhead Service Entrance Cap
Halex Terminal Adapter, 1/2 in Conduit, Male End, PVC, 10 in Length, For Indoor/Outdoor Applications For use with 'A' and 'C' series channel and inserts. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings.
Halex 60416 Light Duty Wire Holder Halex 64407 Conduit Elbow Halex 36019 Ground Clamp
Used indoors or outdoors to secure incoming service entrance wires. Reinforced. Porcelain and steel. Tray box. To connect EMT conduit together to allow for 90 degree bends. UL Approved. Indoor or outdoor applications. Use to secure the grounding wire to a 1/2" through 1" pipe. UL Listed. Wire size fits #10 - #2 AWG.
Halex 20510 Twin Screw Clamp Connector Halex 26571 Flexible MC Snap-In Connector Teddico/BWF 100-CGV Thinwall Conduit Body Assembly
Fits 1/2" knockout, non-metallic cable numbers 14/2, 12/2, 12/3 AWG or 2 number 14/2 AWG or flex cord .300 to .560 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL, Listed, meets CSA requirements. Halex MC Snap-In Connector, Flexible, 3/8 in Nominal, Steel, Includes: Insulating Bushing, CSA Certified, UL Listed, For use to connect aluminum or steel ac, aluminum mc, and steel flexible metal conduit, indoor use only Teddico/BWF Conduit Body Assembly, Thinwall, LR, 1/2 in Hub, 2 Hubs, Right Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, 4.3 in Length, 2.4 in Width, 1.3 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348
Teddico/BWF 200-CGV Thinwall Conduit Body Assembly Teddico/BWF 501V Thinwall Rigid Conduit Entrance Elbow Teddico/BWF 700-CGV Thinwall Conduit Body Assembly
Teddico/BWF Conduit Body Assembly, Thinwall, LL, 1/2 in Hub, 2 Hubs, Left Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, 4.3 in Length, 2.4 in Width, 1.3 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348 Teddico/BWF Conduit Entrance Elbow, Thinwall, SLB, 3/4 in Hub, Rigid Conduit, Threaded Installation, Die Cast Aluminum, Gray, Powder Coated, Includes: Cover and Screw, CSA Certified, UL Listed, For connecting conduit sections, making bends in conduit runs as pull outlets, to provide openings for making splices and taps in conductors Teddico/BWF Conduit Body Assembly, Thinwall, T, 1/2 in Hub, 3 Hubs, Side Access Opening, Tee Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling
Halex 64105 Conduit Elbow Halex 64320 Conduit Nipple Halex 26162 2-Hole Snap-On Conduit Strap
Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Made of steel, fully threaded. Indoor or outdoor. Use to connect two steel outlet boxes or other metal enclosures or to extend a length of threaded Rigid or IMC conduit. Bulk packed. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications.
Superstrut 200 Series Square Conduit Washer Superstrut 200 Series Square Conduit Washer Carlon E983GR-CAR Rigid IMC Conduit Body
GoldGalv finish. GoldGalv finish. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.
Halex 20512 Twin Screw Clamp Connector Teddico/BWF 301-CGV Thinwall Conduit Body Assembly Teddico/BWF 601-CGV Thinwall Conduit Body Assembly
Fits non metallic cable, such as Romex, number 14/2 round, number 12/3-8/3 AWG or flex cord .460 to .720 inches diameter. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requirements. Teddico/BWF Conduit Body Assembly, Thinwall, C, 3/4 in Hub, 2 Hubs, Side Access Opening, Straight Hub, Stamped Aluminum Cover, Threaded Installation, 15-1/2 in Length, 8-1/2 in Width, 5-3/4 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348 Teddico/BWF Conduit Body Assembly, Thinwall, LB, 3/4 in Hub, Back Side Access Opening, Stamped Aluminum Cover, Threaded Installation, 15-1/2 in Length, 8-1/2 in Width, 5-3/4 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling
Steel City R Threaded Rod Carlon Carflex LN43FA-CAR 1-Piece Straight Conduit Connector Carlon E977DC25-UPC Conduit Clamp
Framing and hanging applications. Free-running, corrosion resistant, burr-free. For flexible conduit. Non-metallic/non-conductive, corrosion resistant plastic. Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit.
Carlon E998G-CAR Service Entrance Cap Thomas & Betts E986HR Type LB Rigid/IMC Conduit Body Halex 58607 Rigid Threaded Conduit Body with Cover and Gasket
Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved.
Square D PK7GTACP Ground Bar Kits Eritech CWP1JU Grounding Pipe Clamp Halex 26076 Knock Out Seals
Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Bolted water pipe clamps made from high-strength corrosion-resistant copper alloy. Connects grounding wire to the grounding rod. Range 10 solid - 2 stranded. UL Listed. Use to cover exposed knock-out holes in steel outlet boxes and other metal enclosures.
Halex 58907 Rigid Threaded Conduit Body with Cover and Gasket Halex 20441 Flexible Screw-In Connector Halex 58307 Rigid Threaded Conduit Body with Cover and Gasket
Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed. Halex Screw-In Connector, Flexible, 1/2 in Nominal, 0.92 in Hex, Die Cast Zinc, 1.38 in Length, CSA Certified, UL Listed, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Aluminum, indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Halex 04012 Offset Nipple Carlon UAFAE Flexible Conduit Elbow Thomas & Betts E977NEC-CTN 1-Piece Conduit Clamp
Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. Made of a highly durable plastic (PVC) compound making the product nonmetallic and safe to install. Elbow is non-corrosive, rustproof, and easily pliable. Good for those applications that requires change of direction. UL listed. Drill  5/16'' hole with masonry bit and tap in with hammer.
Halex 26142 Flat Drive Strap Thomas & Betts E977NDC-CTN 1-Piece Conduit Clamp Halex 58407 Rigid Threaded Conduit Body with Cover and Gasket
Indoors or outdoors. To secure EMT conduit to a wood or masonry surface. Drill  5/16'' hole with masonry bit and tap in with hammer. Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved. Tray boxed.
Teddico/BWF 101-CGV Thinwall Conduit Body Assembly Teddico/BWF 201-CGV Thinwall Conduit Body Assembly Teddico/BWF 701-CGV Thinwall Conduit Body Assembly
Teddico/BWF Conduit Body Assembly, Thinwall, LR, 3/4 in Hub, 2 Hubs, Right Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Teddico/BWF Conduit Body Assembly, Thinwall, LL, 3/4 in Hub, 2 Hubs, Left Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, 5 in Length, 2.6 in Width, 1-1/2 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348 Teddico/BWF Conduit Body Assembly, Thinwall, T, 3/4 in Hub, 3 Hubs, Side Access Opening, Tee Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling
26351 RIGID CMPRSN CON STL1/2I Superstrut ZCM1003/8-10 Cone Nut Superstrut ZCM1001/2-10 Cone Nut
Use to join threadless Rigid or IMC conduit to a steel outlet box or other metal enclosure. Concrete-tight. UL, CSA. Superstrut Cone Nut, 3/8 in Nominal, Nylon Cone, Steel Nut, Galvanized, Gold, For Superstrut Metal Framing and Hanger System Superstrut Cone Nut, 1/2 in Nominal, Nylon Cone, Steel Nut, Galvanized, Gold, For Superstrut Metal Framing and Hanger System
Thomas And Betts Z503-5 Superstrut Beam Clamp Halex 07020 Conduit Chase Nipple Halex 63299 Ground Screw
For hanging rod, silver electroplated finish. Zinc die cast. Indoor or outdoor applications. Use to terminate threaded conduit to a knockout box or enclosure, where space within the box is limited. Used with a locknut to provide a short raceway between boxes or enclosures. UL and CSA approved. Indoor or outdoor applications. Use to ground a wiring device to a steel outlet box. Green color.
Carlon UB9AH-CAR Standard Radius Conduit Elbow Halex 91695 Multi-Piece Liquid Tight Conduit Elbow Halex 58010 Clamp On Weatherhead Service Entrance Cap
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Multi-piece, zinc die cast. Use to connect liquid-tight conduit to a steel outlet box or other metal enclosure or hub. UL Listed. Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed.
Carlon E977EC20-UPC Conduit Clamp Halex 27692 Liquid Tight Conduit Elbow Halex 59507 Service Entrance Elbow
Offers same chemical resistance as Carlon nonmetallic conduit for a complete, corrosion resistant system. UV resistant for use in direct sunlight. Use in accordance with conduit spacing requirements per NEC. Each clamp requires 2 screws, 2 nuts, and 2 washers. Gray clamps for standard conduit. Indoors or outdoors, fitting will not rust or corrode. No disassembly required, just hand-tighten nut. Reusable. Use to connect type B non-metallic liquid-tight conduit to a weatherproof outlet box, pool/spa equipment motor, central air conditioning unit or various other electrical enclosures or hubs. UL Approved. Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed.
Halex 96361 Concrete-Tight Conduit Coupling Carlon E987H-CAR Rigid Conduit Body GE TC100P Rainproof Conduit Hub
Halex Conduit Coupling, Concrete-Tight, 1/2 in Conduit, IMC, Rigid Conduit, Compression End, Steel, Galvanized, 1.76 in Length, UL Listed, CSA Certified, 1.17 in Width, For Indoor Applications For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. For outdoor enclosures with removable closing caps.
GE TC125P Rainproof Conduit Hub GE TC150P Rainproof Conduit Hub GE TC200P Rainproof Conduit Hub
For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps. For outdoor enclosures with removable closing caps.
Halex 99526 Insulated Metallic Grounding Conduit Bushing with Lug Halex 61205B 2-Hole Conduit Strap Halex 61212B 2-Hole Conduit Strap
Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved.
Carlon E983H-CAR Rigid IMC Conduit Body Carlon E998H-CAR Standard Weatherhead Service Entrance Cap Halex 57499 Oval Standard Service Cable Cap IMC
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings. Copper-free aluminum die cast. Indoor or outdoor applications. Use in overhead services that utilize SEU cable. Tray boxed.
Halex 58012 Clamp On Weatherhead Service Entrance Cap Halex 64410 Conduit Elbow Carlon UA9AK-CAR Standard Radius Conduit Elbow
Aluminum die cast. Indoor or outdoor applications. Use in an overhead service entrance. Mounts on top of EMT, Rigid or IMC conduit. Serves as a connecting point for the service entrance wires. UL Listed meets CSA requirements. Tray boxed. To connect EMT conduit together to allow for 90 degree bends. UL Approved. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant.
Carlon E987G-CAR Rigid Conduit Body Schneider PK9GTACP Ground Bar Kit Square D PK12GTACP Ground Bar Kits
For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed.
Halex 58807 Rigid Threaded Conduit Body with Cover and Gasket Halex 20442 Flexible Screw-In Connector Teddico/BWF 502V Thinwall Rigid Conduit Entrance Elbow
Copper-free die cast aluminum. Indoors or outdoors. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. UL Approved. Tray boxed. Halex Screw-In Connector, Flexible, 3/4 in Nominal, 1.12 in Hex, Die Cast Zinc, 1.62 in Length, CSA Certified, UL Listed, For use to connect flexible metallic conduit to steel outlet box, load center or other metal enclosure, indoor use only Teddico/BWF Conduit Entrance Elbow, Thinwall, SLB, 1 in Hub, Rigid Conduit, Threaded Installation, Die Cast Aluminum, Gray, Powder Coated, Includes: Cover and Screw, CSA Certified, UL Listed, For connecting conduit sections, making bends in conduit runs as pull outlets, to provide openings for making splices and taps in conductors
Halex HX Rigid Conduit Connector Halex 64107 Conduit Elbow Raco 8983-1 Ground Pigtail
Halex Conduit Connector, Rigid, Series: HX, 1 in Nominal, Compression End, Straight, Steel, CSA Certified, UL Listed, 1 in Male NPSM Hub, For use to connect and effectively bond rigid or imc conduit to a steel outlet box or other metal enclosure Use to allow a 90 degree change of direction in a run of Rigid or IMC conduit. UL Listed. Raco Ground Pigtail, Terminal Type NO 10-32 TPI Hex/Phillips/Slotted Head Screw, 12 AWG, Copper, Green, 6 in Length, Includes: 4-Way Combo Head Ground screw, For Steel Box
Steel City R Threaded Rod BUSHING GRND MTL INSUL 1-1/4IN Siemens EC38599 Type RX Conduit Hub
Framing and hanging applications. Free-running, corrosion resistant, burr-free. Zinc die cast. Rounded surface prevents damage to insulation. Thermoplastic liner rated at 150 degree F. Indoor or outdoor use. Use with locknut to terminate service conduit to a cabinet. Lug provided for bonding jumper to a neutral bus bar. UL Listed, CSA Approved. For use on all Siemans and Murry single position meter sockets.
Eritech EK17 Direct Burial Perpendicular Ground Clamp Eritech EK16 Direct Burial Ground Clamp Cutler-Hammer GBK10P Ground Bar Kits
Bronze alloy grounding clamp with bronze screws. Used for rebar, ground rods, water pipes and direct-burial water pipe. Lay-in feature cuts installation time. Approved for direct burial in earth and concrete. Pipe range from 1/2" (12.7 mm) to 1" (25.4 mm). Rebar range from #4 (10 mm) to #8 (25 mm). Ground rod range from 1/2" (12.7 mm) to 1" (25.4 mm). Conductor range from #10 (5.5 mm sq) to #2 (25 mm sq). UL listed. Bronze alloy grounding clamp with bronze screws. Used for rebar, ground rods, water pipes and direct-burial water pipe. Lay-in feature cuts installation time. Approved for direct burial in earth and concrete. Pipe range from 1/2" (12.7 mm) to 1" (25.4 mm). Rebar range from #4 (10 mm) to #8 (25 mm). Ground rod range from 1/2" (12.7 mm) to 1" (25.4 mm). Conductor range from #10 (5.5 mm sq) to #2 (25 mm sq). UL listed. Bar wire holes are suitable for (1) #14-4 or up to (3) #14-10 aluminum or copper wire. Multiple wires in a single hole must be of the same size and material. Distance between mounting holes is 1-3/4". NOTE: Consult local code for correct application of ground bar kit for service entrance equipment. Kit contains one ground bar and two #10-32 x 5/8" self-threading screws. UL Listed.
Thomas & Betts E970CDE-CTN Rigid/Non-Metallic Junction Box Halex 64020 Conduit Coupling Siemens EC38597 Type RX Conduit Hub
Four knock-out type socket openings, 90 degree spacing. Includes separate mounting feet, cover and gasket. Non-conductive. Will not rust or corrode. Steel, indoor or out. Use to join threaded Rigid or IMC conduit together. UL Listed. For use on all Siemans and Murry single position meter sockets.
Siemens EC38598 Type RX Conduit Hub Halex 20492 Combination Coupling Teddico/BWF 102-CGV Thinwall Conduit Body Assembly
For use on all Siemans and Murry single position meter sockets. Use to joint EMT conduit to flexible metal conduit. Die cast zinc. UL Approved, CSA Certified. Teddico/BWF Conduit Body Assembly, Thinwall, LR, 1 in Hub, 2 Hubs, Right Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, 5.8 in Length, 2.9 in Width, 1.8 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348
Teddico/BWF 302-CGV Thinwall Conduit Body Assembly Teddico/BWF 602-CGV Thinwall Conduit Body Assembly Halex 36020 Ground Clamp
Teddico/BWF Conduit Body Assembly, Thinwall, C, 1 in Hub, Side Access Opening, Straight Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Teddico/BWF Conduit Body Assembly, Thinwall, LB, 1 in Hub, Back Side Access Opening, Stamped Aluminum Cover, Threaded Installation, 15-1/2 in Length, 8-1/2 in Width, 5-3/4 in Depth, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Wire size fits #10 - #2 AWG. Use to secure the grounding wire to a 1-1/4" - 2" or 2-1/2" - 4" pipe. Bronze. UL Listed.
Carlon UB9AJ-CAR Standard Radius Conduit Elbow Square D PK15GTACP Ground Bar Kits Halex 58610 Rigid Threaded Conduit Body with Cover and Gasket
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Aluminum, indoor or outdoor. Use to gain access to the interior of a raceway for wire pulling, splicing (with limitations as specified by the NEC), and maintenance. With cover and gasket. UL Approved.
Carlon UAFAF Conduit Elbow Siemens EC2GB152 Ground Bar Kit With Terminal 2/0 Lug Siemens ECHS125 Type HS Conduit Hub
Made of a highly durable plastic (PVC) compound making the product nonmetallic and safe to install. Elbow is non-corrosive, rustproof, and easily pliable. Good for those applications that requires change of direction. UL listed. For equipment grounding provision. #14 to 4 AWG, 60/75 degree Celsius, Cu/A1. For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225.
Halex 04015 Offset Nipple Halex 61615B 2-Hole Snap-On Conduit Strap Halex 64356 Conduit Nipple
Zinc die cast. Use as an offset connector between two enclosures. Offsets the axis of the raceway 3/4". UL Approved. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Used to connect two steel outlet or other steel boxes. Indoor or outdoor use. Made of steel with National Pipe Standard threading.
Teddico/BWF 702-CGV Thinwall Conduit Body Assembly Cutler-Hammer GBK14P Ground Bar Kits Halex 64412 Conduit Elbow
Teddico/BWF Conduit Body Assembly, Thinwall, T, 1 in Hub, 3 Hubs, Side Access Opening, Tee Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling Bar wire holes are suitable for (1) #14-4 or up to (3) #14-10 aluminum or copper wire. Multiple wires in a single hole must be of the same size and material. Distance between mounting holes is 1-3/4". NOTE: Consult local code for correct application of ground bar kit for service entrance equipment. Kit contains one ground bar and two #10-32 x 5/8" self-threading screws. UL Listed. To connect EMT conduit together to allow for 90 degree bends. UL Approved.
Erico 815860UPC Grounding Rods Thomas & Betts E986J-CTN Type LB Rigid/IMC Conduit Body Halex 60222 Wire Holder
Zinc-coated exteriors are hot-dip galvanized for solid protection against corrosion in accordance with ASTM specification A153-78. Surfaces are rigidly inspected to eliminate seams, slivers and other defects. Meet EEI-NEMA TDJ-30 and are REA listed. 15 year service life in most soils. Galvanized plated steel. Rigid non-metallic Type LB conduit body. For easy access and pulling of wires through conduit run. For use with Schedule 40 non-metallic solvent weld fittings. Will not rust or corrode. With textured lid and foam-in-place gasket. Hubs are not threaded. UL Listed, RoHS Compliance. Used indoors or outdoors to secure incoming service entrance wires. Reinforced. Porcelain and steel. Tray box.
Carlon E950KJ-CAR Reducing Conduit Bushing Siemens ECHS150 Type HS Conduit Hub Teddico/BWF 202-CGV Thinwall Conduit Body Assembly
For connecting different sizes of conduit. Socket both ends, for reducing male Schedule 40/80 conduit runs or fittings to female. Non-conductive. Will not rust or corrode. For use on all Siemens loadcenters, main lug, main breaker and meter socket; plus enclosed circuit breakers Nos. WB2225, WB3225. Teddico/BWF Conduit Body Assembly, Thinwall, LL, 1 in Hub, Left Side Access Opening, 90 deg Hub, Stamped Aluminum Cover, Threaded Installation, Die Cast Aluminum, Neoprene Gasket, Gray, Includes: Cover and Gasket, UL 514B, UL E121488, CSA C22.2 No. 18, CSA LR57925, NEMA FB-1, NEC Article 348, For Wire Pulling
LOCK NUT SEALER 2IN           Halex 61215B 2-Hole Conduit Strap Halex 91697 Multi-Piece Liquid Tight Conduit Elbow
LOCK NUT SEALER 2IN
Our Price: $8.69
Secures rigid or IMC conduit, or threaded fittings to steel outlet boxes or other steel boxes where moisture proofing is needed. Steel with zinc plating, pre-molded seal on one side. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. Indoors or outdoors. Multi-piece, use to connect flexible metallic or type B non-metallic liquid-tight conduit to a steel outlet box, metal enclosure or hub.
Square D PK23GTACP Ground Bar Kits Eritech 615840UPC Grounding Rod Carlon UA7AK-CAR Standard Radius Conduit Elbow
Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. Copperbonded, resists corrosion better than galvanized rods, allowing for a 30-year service life in most soils. Uniform plating thickness, average tensile strength of 80,000 psi and straightness tolerance of .010" per linear foot. Exceeds the requirements of ANSI/UL 467-1984, CSA, and ANSI/NEMA GR-1. For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. UL Listed E35297.
Halex 61505B 1-Hole Snap-On Cable Strap Eaton DS125H1P Rainproof Conduit Hub Eaton DS150H1P Rainproof Conduit Hub
Indoor or outdoor applications. To support EMT conduit. For use with MLO and MCB loadcenters and circuit breaker enclosures. For use with MLO and MCB loadcenters and circuit breaker enclosures.
Halex 59510 Service Entrance Elbow Halex 61605B 2-Hole Snap-On Conduit Strap Carlon E998J-CAR Service Entrance Cap
Copper-free die cast aluminum. Use to gain access to the interior of a raceway for wire pulling, inspection and maintenance. UL Approved. Tray boxed. To support EMT conduit where greater load bearing is required. Indoor or outdoor applications. Safe, non-conductive. To bring overhead wiring from outside into conduit run. Will not rust or corrode. For use with Schedule 40/80 non-metallic solvent weld fittings.
Halex 58015 Clamp On Weatherhead Service Entrance Cap Halex 29523 Insulated Metallic Grounding Conduit Bushing with Lug